plumiOrthographic third angle projection drawings: OCR Level 1/2 Engineering Manufacture questions
Every OCR Level 1/2 Engineering Manufacture exam question on 3.1 Orthographic third angle projection drawings, 2024–2025, with its mark scheme and examiner’s report.
Paper
All papers
Exam
All years
- Your answer
- Your answer
- Your answer
Q14(a)
The whole paper ↗0 wordsQ16(a)(i)
The whole paper ↗0 wordsQ16(a)(ii)
The whole paper ↗0 wordsQ16(a)(iii)
The whole paper ↗0 wordsQ16(a)(iv)
The whole paper ↗0 wordsQ16(b)(i)
The whole paper ↗0 wordsQ16(b)(ii)
The whole paper ↗0 words- Your answer
- Your answer
Q14(a)
The whole paper ↗0 wordsQ14(b)
The whole paper ↗0 words- Your answer
- Your answer
Q14(a)
The whole paper ↗0 wordsQ14(b)
The whole paper ↗0 wordsQ14(c)
The whole paper ↗0 words- Your answer
All 21 questions on Orthographic third angle projection drawings, as a list
- June 2025, R014, Q5 (1 mark): What does this symbol represent on an engineering drawing? (a) Countersink (b) Knurl (c) Thread (d) Tolerance [1]
- June 2025, R014, Q10 (1 mark): According to BS 8888, what is the correct abbreviation for drawing? (a) DGR (b) DGW (c) DRG (d) DRW [1]
- January 2025, R014, Q6 (1 mark): What is BS 8888 the standard for? (a) Engineering drawing conventions (b) Environmental practices (c) Finishing processes (d) Waste management procedures [1]
- January 2025, R014, Q14(a) (2 marks): Calculate the maximum and minimum acceptable diameters for the hole. Maximum Minimum [2]
- January 2025, R014, Q16(a)(i) (1 mark): AF [1]
- January 2025, R014, Q16(a)(ii) (1 mark): DIA [1]
- January 2025, R014, Q16(a)(iii) (1 mark): MAT [1]
- January 2025, R014, Q16(a)(iv) (1 mark): SQ [1]
- January 2025, R014, Q16(b)(i) (2 marks): [2]
- January 2025, R014, Q16(b)(ii) (2 marks): [2]
- June 2024, R014, Q7 (1 mark): What type of line is this on an orthographic drawing? (a) Dimension (b) Leader line (c) Outline (d) Projection [1]
- June 2024, R014, Q10 (1 mark): Which of these is represented by a patterned surface on an orthographic drawing? (a) Chamfer (b) Countersink (c) Hole (d) Knurl [1]
- June 2024, R014, Q14(a) (2 marks): State two mechanical features shown by label A. 1 2 [2]
- June 2024, R014, Q14(b) (1 mark): State the dimension shown by label B. 30 mm [1]
- January 2024, R014, Q6 (1 mark): What does the abbreviation CL mean on an orthographic drawing? (a) Centre lathe (b) Centre line (c) Contour line (d) Controlled link [1]
- January 2024, R014, Q10 (1 mark): A dimension is given on an engineering drawing as 20.00 mm ±0.05. Which is the maximum allowed dimension? (a) 19.95 mm (b) 20.05 mm (c) 20.10 mm (d) 20.50 mm [1
- January 2024, R014, Q14(a) (2 marks): Identify the standard drawing convention labelled A, giving the dimension shown. [2]
- January 2024, R014, Q14(b) (2 marks): Identify the standard drawing convention labelled B, giving the dimension shown. [2]
- January 2024, R014, Q14(c) (6 marks): Consider the following statement: A pillar drill and centre lathe are the machines that could be used to manufacture the slotted bracket shown in Fig. 5 with C
- Specimen, R014, Q7 (1 mark): On an orthographic drawing, what is the meaning of the type of line shown in Fig.1? Fig.1 (a) Centre line (b) Hidden detail (c) Leader line (d) Outline [1]
- Specimen, R014, Q8 (1 mark): On an orthographic drawing, what is the meaning of the symbol shown in Fig.2? Ø Fig.2 (a) Diameter (b) Knurl (c) Radius (d) Thread size [1]
Questions, mark schemes and examiner’s reports are © OCR, from their published past papers. Plumi isn’t affiliated with any exam board. Want whole papers? Full past papers.
Rather write your answers by hand on iPad? Plumi marks them against the same mark schemes.