Skip to content
Android waitlistTry on iPad
Get started

Mechanical devices: Eduqas GCSE Design and Technology questions

Eduqas GCSE Design and Technology past-paper questions on T7 Mechanical devices, 2019–2025, with mark schemes and examiner’s reports where available.

Past paper difficulty
Paper
All papers
Exam
All years
Calculations

Loading the full question list…

599 questions

  1. Q3(a)(i)

    June 2025 · Section A · ★★★

    The whole paper ↗
    1
    Original question 3(a)(i): Using examples of other products, complete the table below by naming a product that uses each of the motions listed. 3 x [1] Motion Product Linear Reciprocating

    Loading the question…

  2. Q3(a)(ii)

    June 2025 · Section A · ★

    The whole paper ↗
    2
    Original question 3(a)(ii): A bicycle brake system uses a bell crank lever. State the function of a bell crank lever. [1]

    Loading the question…

  3. Q3(b)(i)

    June 2025 · Section A · ★

    The whole paper ↗
    3
    Original question 3(b)(i): The driven wheel of the bicycle’s gear system has 10 teeth and the driver wheel has 40 teeth. State how many rotations the driven gear makes if the driver gear

    Loading the question…

  4. Q3(b)(ii)

    June 2025 · Section A · ★★★

    The whole paper ↗
    4
    Original question 3(b)(ii): The diameter of the bicycle’s wheel is 60 cm. Calculate the distance in metres the electric bicycle will travel after ten rotations. Show all workings. [3]

    Loading the question…

  5. Q3(b)(iii)

    June 2025 · Section A · ★★

    The whole paper ↗
    5
    Original question 3(b)(iii): Other than cost, explain why a cyclist would buy a non-electric bicycle instead of an electric one. [2]

    Loading the question…

  6. Q3(a)(i)

    June 2024 · Section A · ★

    The whole paper ↗
    6
    Original question 3(a)(i): State the type of motion the record will take when being played. [1]

    Loading the question…

  7. Q3(a)(ii)

    June 2024 · Section A · ★

    The whole paper ↗
    7
    Original question 3(a)(ii): State the meaning of rpm. [1] R …… …… P …… M …… …

    Loading the question…

  8. Q3(a)(iii)

    June 2024 · Section A · ★

    The whole paper ↗
    8
    Original question 3(a)(iii): Put a tick (√) in the grid below to indicate which record speed would take longer to play. [1] 33rpm 45rpm Record

    Loading the question…

  9. Q3(a)(iv)

    June 2024 · Section A · ★★

    The whole paper ↗
    9
    Original question 3(a)(iv): Calculate the number of times a 45 rpm record will rotate in 4 minutes. Show all workings. [2]

    Loading the question…

  10. Q3(b)(i)

    June 2024 · Section A · ★★

    The whole paper ↗
    10
    Original question 3(b)(i): Calculate the velocity ratio of the driven pulley. [2] Show all workings.

    Loading the question…

  11. Q3(b)(ii)

    June 2024 · Section A · ★★★★

    The whole paper ↗
    11
    Original question 3(b)(ii): Describe the differences between a simple gear train and a pulley and belt drive.  [4]

    Loading the question…

  12. Q3(c)(i)

    June 2023 · Section A · ★★

    The whole paper ↗
    12
    Original question 3(c)(i): The handle turns the drive gear which has 32 teeth and the driven gear which has 16 teeth. Calculate the gear ratio. [2] Show all workings.

    Loading the question…

  13. Q3(c)(ii)

    June 2023 · Section A · ★★

    The whole paper ↗
    13
    Original question 3(c)(ii): If the handle rotates three times, calculate how many full rotations the merry-go-round will make. [2] Show all workings.

    Loading the question…

  14. Q3(c)(iii)

    June 2023 · Section A · ★★★

    The whole paper ↗
    14
    Original question 3(c)(iii): Using an example of a named product explain the motion of a rack and pinion gear. [3] Name of Product: 

    Loading the question…

  15. Q6(a)(v)

    June 2023 · Section B · ★★★★

    The whole paper ↗
    15
    Setup for original question 6(a)(v)

    Loading the question setup…

    Original question 6(a)(v): The image below shows a simple pulley system. In the space below, use notes and sketches to show how the pulleys can be modified to turn at the same speed and i

    Loading the question…

  16. Q2(a)(i)

    June 2022 · Section A · ★

    The whole paper ↗
    16
    Original question 2(a)(i): State the function of the Cams on the Automata Toy. [1]

    Loading the question…

  17. Q2(a)(ii)

    June 2022 · Section A · ★★

    The whole paper ↗
    17
    Original question 2(a)(ii): Draw arrows to correctly identify the Cam and the Follower on the image below. [2] Follower Cam

    Loading the question…

  18. Q2(b)

    June 2022 · Section A · ★★

    The whole paper ↗
    18
    Original question 2(b): The image below shows a pear-shaped Cam. Describe the motion produced by this mechanism. [2]

    Loading the question…

  19. Q2(c)

    June 2022 · Section A · ★★

    The whole paper ↗
    19
    Original question 2(c): The image below shows a lever system used to crush aluminium cans ready for recycling. Draw arrows to correctly label the effort and load. [2]

    Loading the question…

  20. Q3(a)(i)

    Autumn 2021 · Section A · ★★

    The whole paper ↗
    20
    Original question 3(a)(i): Read the following two statements and circle if they are True or False. A pulley is a wheel with a groove running around the outside. True or False [1] The dron

    Loading the question…

All 36 questions on Mechanical devices, as a list
  1. June 2025, Section A, Q3(a)(i) (3 marks): Using examples of other products, complete the table below by naming a product that uses each of the motions listed. 3 x [1] Motion Product Linear Reciprocating
  2. June 2025, Section A, Q3(a)(ii) (1 mark): A bicycle brake system uses a bell crank lever. State the function of a bell crank lever. [1]
  3. June 2025, Section A, Q3(b)(i) (1 mark): The driven wheel of the bicycle’s gear system has 10 teeth and the driver wheel has 40 teeth. State how many rotations the driven gear makes if the driver gear
  4. June 2025, Section A, Q3(b)(ii) (3 marks): The diameter of the bicycle’s wheel is 60 cm. Calculate the distance in metres the electric bicycle will travel after ten rotations. Show all workings. [3]
  5. June 2025, Section A, Q3(b)(iii) (2 marks): Other than cost, explain why a cyclist would buy a non-electric bicycle instead of an electric one. [2]
  6. June 2024, Section A, Q3(a)(i) (1 mark): State the type of motion the record will take when being played. [1]
  7. June 2024, Section A, Q3(a)(ii) (1 mark): State the meaning of rpm. [1] R …… …… P …… M …… …
  8. June 2024, Section A, Q3(a)(iii) (1 mark): Put a tick (√) in the grid below to indicate which record speed would take longer to play. [1] 33rpm 45rpm Record
  9. June 2024, Section A, Q3(a)(iv) (2 marks): Calculate the number of times a 45 rpm record will rotate in 4 minutes. Show all workings. [2]
  10. June 2024, Section A, Q3(b)(i) (2 marks): Calculate the velocity ratio of the driven pulley. [2] Show all workings.
  11. June 2024, Section A, Q3(b)(ii) (4 marks): Describe the differences between a simple gear train and a pulley and belt drive.  [4]
  12. June 2023, Section A, Q3(c)(i) (2 marks): The handle turns the drive gear which has 32 teeth and the driven gear which has 16 teeth. Calculate the gear ratio. [2] Show all workings.
  13. June 2023, Section A, Q3(c)(ii) (2 marks): If the handle rotates three times, calculate how many full rotations the merry-go-round will make. [2] Show all workings.
  14. June 2023, Section A, Q3(c)(iii) (3 marks): Using an example of a named product explain the motion of a rack and pinion gear. [3] Name of Product: 
  15. June 2023, Section B, Q6(a)(v) (4 marks): The image below shows a simple pulley system. In the space below, use notes and sketches to show how the pulleys can be modified to turn at the same speed and i
  16. June 2022, Section A, Q2(a)(i) (1 mark): State the function of the Cams on the Automata Toy. [1]
  17. June 2022, Section A, Q2(a)(ii) (2 marks): Draw arrows to correctly identify the Cam and the Follower on the image below. [2] Follower Cam
  18. June 2022, Section A, Q2(b) (2 marks): The image below shows a pear-shaped Cam. Describe the motion produced by this mechanism. [2]
  19. June 2022, Section A, Q2(c) (2 marks): The image below shows a lever system used to crush aluminium cans ready for recycling. Draw arrows to correctly label the effort and load. [2]
  20. Autumn 2021, Section A, Q3(a)(i) (2 marks): Read the following two statements and circle if they are True or False. A pulley is a wheel with a groove running around the outside. True or False [1] The dron
  21. Autumn 2021, Section A, Q3(a)(ii) (2 marks): The diagram below shows the pulley system used in the drone. Driven Driver Pulley Pulley Explain why the driven pulley rotates slower than the driver pulley. [2
  22. Autumn 2021, Section A, Q3(a)(iii) (2 marks): The pulley system has a velocity ratio of 1:2. The speed of the driver pulley is 20 revolutions per minute. Calculate the speed of the driven pulley. Show all w
  23. Autumn 2021, Section A, Q3(a)(iv) (3 marks): The pulley system shown below uses two pulleys both of equal size. NOTE: sizes in millimetres. 50 Pulley Pulley ∅20 ∅20 Calculate the length of the pulley belt
  24. Autumn 2021, Section A, Q3(a)(v) (2 marks): Explain one advantage of using a pulley system when developing the design of the drone. [2]
  25. Autumn 2020, Section A, Q3(a)(i) (2 marks): Identify the type of mechanical motion used by each product. 2 × [1] Needle Wheel motion motion Motion: Motion:
  26. Autumn 2020, Section A, Q3(a)(ii) (2 marks): Explain how one of the mechanical motions in (i) above functions. [2]
  27. Autumn 2020, Section A, Q3(b)(i) (2 marks): The rider of a bicycle turns the pedal crank 36 times in 30 seconds. Calculate the speed of the pedal crank in rpm (revolutions per minute). [2] Show all workin
  28. Autumn 2020, Section A, Q3(b)(ii) (2 marks): The diagram below shows a gear system used on a bicycle. FRONT REAR 12 teeth 48 teeth Calculate the ratio of the gears used on the bicycle. [2] Show all working
  29. Autumn 2020, Section A, Q3(b)(iii) (2 marks): Using the word bank below, correctly complete the statement that follows: Fulcrum Force Lever Load The handbrake on a bicycle is a and the point at which the br
  30. June 2019, Section A, Q3(b)(i) (4 marks): Calculate both the mechanical advantage and velocity ratio of the see-saw. (Show all workings.) 2 × [2] Mechanical Advantage: Velocity Ratio:
  31. June 2019, Section A, Q3(b)(ii) (1 mark): Explain the role of the fulcrum in the see-saw. [1]
  32. June 2019, Section A, Q3(b)(iii) (1 mark): State what would happen if you changed the position of the fulcrum. [1]
  33. June 2019, Section B, Q6(b)(i) (1 mark): Calculate the diameter of the wheel. [1]
  34. June 2019, Section B, Q6(b)(ii) (2 marks): Calculate the circumference of the wheel. [2]
  35. June 2019, Section B, Q6(b)(iii) (1 mark): Calculate how far the robotic cleaner will have travelled before it returns to the docking station. [1]
  36. June 2019, Section B, Q6(b)(iv) (1 mark): Round off your answer in (iii) above to the nearest metre. [1]

Questions, mark schemes and examiner’s reports are © WJEC Eduqas, from their published past papers. Plumi isn’t affiliated with any exam board. Want whole papers? Eduqas GCSE Design and Technology past papers.

The Plumi iPad app also offers exam-style questions with AI feedback on your handwritten working.